Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sailorman

Pages: 1 [2]
16
LIKE 200i / Re: New to me 2012 - need advice
« on: February 02, 2019, 08:05:36 PM »
Thanks for advice guys and for posting all this great material on the site and on YouTube. Drained oil and changed oil in gearbox.  Pulled seat and cleaned up, then checked valves.  Upper one was fine;gap on lower one was very tight, less than .05mm.  Readusted it to .102mm.  Replaced plug with NGK Iridium. The Iridium plug looks to project much farther into the cylinder than the OEM one; hope that will not be a problem.  As soon as GY6 strainer plug arrives on slow boat from Shanghai will replace that, fill with 15W40, and test ride.  Again, thanks!

17
LIKE 200i / Re: Oil strainer plug cap replacement?
« on: January 29, 2019, 03:25:50 PM »
Thanks guys, that is helpful. Bought a 6-point 17mm socket today!

18
Eye Candy | Videos and Pics / Re: Cool scooter pix....
« on: January 28, 2019, 08:40:30 PM »
At Xmas festival in Iraklion, Crete

19
LIKE 200i / Oil strainer plug cap replacement?
« on: January 28, 2019, 08:26:27 PM »
OK, managed to round/strip the oil strainer plug cap part or "oil tappet cap" #12361   as I did not realize it was aluminum and used a 12-point socket on it.  Finally got it off today with a cold chisel and plenty of penetrant.  Old gunner's mate guideline: if it doesn't come out, use a bigger hammer.

Trying to order replacement but Kymco Monster shows "not available."  Is it safe to assume one of the inexpensive GY6 strainer sets like these available online will fit the 200i?

https://www.amazon.com/Scooter-Drain-Spring-Filter-125cc/dp/B00GIZCCNO

https://www.amazon.com/TC-Motor-Strainer-Screen-Chinese-Scooter/dp/B01MS8O0F6/ref=pd_lpo_vtph_263_lp_t_3?_encoding=UTF8&psc=1&refRID=EVKHTFDSA9CE5FDC9F77

20
LIKE 200i / Re: 2012 Like 200i: Swap push button release for lockset?
« on: January 26, 2019, 09:38:16 PM »
Looks just like your installation!

21
LIKE 200i / Re: 2012 Like 200i: Swap push button release for lockset?
« on: January 25, 2019, 10:46:07 PM »
I bought/installed the 1 3/8" model.  Required a couple of extra stainless washers and grommets, easily found at local Ace.  Installed and it works!

22
LIKE 200i / New to me 2012 - need advice
« on: January 20, 2019, 10:44:25 PM »
Hi All, just joined forum. Have run a Honda Metropolitan for a while but it always felt too small.  I just purchased a 2012 200i with 860 miles on it for $500.  It seems in very good shape, but has been siting unused for last two years due to original owner losing interest.  I topped off oil, inflated tires (OEM Kendas), and adjusted suspension.  The battery seems strong.  Had it up to 65 MPH on back road, no issues noted.  Planned to start off with a state inspection, then take it to a trusted local motorcycle shop as there is no Kymco dealership within many many miles.

Aside from an oil and gearbox lube change, air filter blow out, what should I ask them (the mechanics) to do or check to get this cycle ready for safe daily use?

Pages: 1 [2]