1
Side By Side / Re: 09 uvx 500 only runs with choke
« on: February 18, 2021, 06:35:50 PM »
Plugged pilot jet, need to take carb fully apart and clean.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Side By Side / Re: 2013 uxv500i clutch
« on: November 24, 2020, 03:08:21 AM »
Definately 14g OD weights and EPI white spring! Very strong trail response and topend improvement!
3
Side By Side / Re: Adding an LED 12" light
« on: November 24, 2020, 03:04:35 AM »
I added a 42" light bar on my 500se years ago and have no issues since.
4
Side By Side / Re: Plow
« on: November 02, 2020, 10:22:38 PM »
Try American Manufacturing, Eagle Plows. I see they make a mount for the 450. I'vee had mine on my uxv500se for 5 years now. Very well made!
5
Side By Side / Re: 2013 uxv500i clutch
« on: October 11, 2020, 02:49:51 PM »
Yamaha rhino 660 parts work in the clutch. Current set up for my 2013 is JBS 14g OD weights and EPI purple spring. Great response in the trail but only 42-43 mph top end. I will be changing back to the EPI white spring as I was running 47-48mph with that during testing. I'm told the real sweet spot is a combo of 12-14g OD weights.
6
Side By Side / Re: 2012 500i UXV speed tips?
« on: January 10, 2020, 02:05:41 AM »
Overdrive clutch weights.
7
Side By Side / Re: Top speed?
« on: November 07, 2019, 12:09:29 AM »
My uxv 500 used to top out at 45mph now i'm around 49-50mph, yes gps verified. A few mods helped!
8
Side By Side / Re: half doors
« on: December 09, 2018, 05:00:56 PM »
Your dealer can order them as they were an option and come standard on the SP.
9
Side By Side / Re: Front mount plow
« on: December 14, 2017, 03:46:54 AM »
Check out Eagle plows as they are american made and very good quality. I've had mine for 4yrs and have had zero issues. Reasonably priced also.
10
Side By Side / Re: 500I Uxv exhaust mods?
« on: November 09, 2017, 02:08:15 AM »
You are welcome! The factory always leaves something on the table, the info is an FYI based on research for those who might want to modify their machine to their liking. I have had no issue with the reliability of my machine, and it is not babied...
11
Side By Side / Re: 500I Uxv exhaust mods?
« on: November 05, 2017, 10:30:11 PM »
Ok here is the update on this so far. Finally someone has made an exhaust for these, google GSE performance. Doebeck makes fuel controllers for these machines for the airbox mod and uni filter. Led light bars are easy to adapt, lighted whip antennas are a most for personality, aslo added a rear bumper and plow.This machine has been fun modifying as there are many options out there to make it your own!
12
Side By Side / Re: 500I Uxv exhaust mods?
« on: January 04, 2016, 12:45:59 AM »
Who has the best clutch kit or does machine of them? Does any one have pics of intake mods? I'm running a uni filter set up now. What muffler? Harder out of the hole and 50mph would be great!
13
Side By Side / Re: 500I Uxv exhaust mods?
« on: December 29, 2015, 04:39:37 PM »
It's too bad support is so low. These could be some bad... machines with the right mods, the base is there. 36HP from a 500! With the right support these really could take off. Everyone loves to tinker, not everyone has 20k to slap down on the latest and greatest.
14
Side By Side / 500I Uxv exhaust mods?
« on: December 28, 2015, 07:16:36 PM »
Has anyone performed any exhaust mods such as removing baffles or reworking the tip like the rhinos. Or just plain old remove the tip for better performance? There has to be something one can do to increase the performance of these machines. I really like the machine but we need some aftermarket or factory support.
Pages: [1]