Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dreflu

Pages: [1] 2 3 ... 10
1
People 50 / Re: Malossi rubber adapter for 19mm carburetor
« on: October 10, 2017, 11:34:22 AM »
I have the dellorto black racing phgb 19mm carburetor. I can see my order from where I ordered the rubber adapter. It says carburetor adapter malossi for kymco sf10. Got it from racing planet

2
People 50 / Re: Malossi rubber adapter for 19mm carburetor
« on: October 08, 2017, 03:03:06 PM »
Any help?

3
People 50 / Malossi rubber adapter for 19mm carburetor
« on: October 06, 2017, 04:27:19 PM »
Hi everybody... its been a while!! I have a cobra/topboy. Sf10 motor same as the people. And I can't find the rubber adapter that makes the delortto carb fit. Mine finally split. Help please!!

4
People 50 / prime oil pump?
« on: March 25, 2014, 11:24:48 AM »
I have the cobra 2t same as people and I pulled the oil pump a while back and it never worked again. anybody know how to prime the oil pump on these?

5
People 50 / Re: 2t cranks right up then dies
« on: March 22, 2014, 11:35:59 AM »
anything?

6
People 50 / Re: 2t cranks right up then dies
« on: March 21, 2014, 12:23:19 PM »
could this be the stator? or does it just go? dirt somewhere?

7
People 50 / Re: cobra only starts after high pitch whine
« on: March 21, 2014, 12:20:00 PM »
I don't know what its called but its a small box that has something to do with the starter in there. it clicks or something. that might be it. green and red wires maybe?

8
People 50 / 2t cranks right up then dies
« on: March 21, 2014, 12:14:40 PM »
I have a 01 kymco cobra( same engine as the people) with a malossi 70cc kit and a arreche carb. it started running funny right before I put it up last year. when I crank it the first time it might be fine for 30 seconds or so then it dies. then every time you start it it runs for a few seconds then dies. ive tried using different jets, new cdi coil straight wired the kill switch checked the grounds even tried the ignition switch off another scoot. nothing gives me any better results. I did a leak down test and she holds 6lbs for 6 mins too.

anybody have any ideas? im lost!!

9
General Discussion / Re: wont start.... help
« on: April 23, 2011, 03:17:03 PM »
its a new beast!!

10
People 50 / Re: Am I wasting my time??
« on: March 23, 2011, 03:45:29 PM »
im pretty sure you're gonna need the pipe for that. i took my pipe technigas pipe off to try something on the another scoot and lost all kinds of power and a good bit off my top end...... just my 2 cents

11
General Discussion / Re: how do you check an oil pump?
« on: March 12, 2011, 11:46:43 AM »
Quote from: Whisper on March 09, 2011, 05:21:50 PM
Don't buy new rings just yet!  That bucket is brand new - The compression will be all over the place until it wears in.  There is no way you could have ruined it that quickly.

Before you compression test put a SMALL amount of oil in the cylindar and cycle it a few times.  If it is bone dry, you'll get bad readings too.


thanks... i opened it up and they look good

12
People 50 / Re: P50 starts and idles, but boggs down if you give it gas
« on: March 08, 2011, 12:51:30 PM »
two stroke or 4? i was having this same problem.

13
General Discussion / Re: Helmet's Full Face or Other
« on: March 05, 2011, 03:22:06 PM »
motorcycle helmet. cover as much of your face as you can. if something ever happens you will be so glad you had the protection.

14
General Discussion / Re: how do you check an oil pump?
« on: March 05, 2011, 12:28:43 AM »
Quote from: Whisper on March 05, 2011, 12:17:22 AM
Dreflu - Don't risk that new cylinder with the stock oil injection pump!  Moving up in CCs changes the motor's needs - ESPECIALLY if you have to rejet/replace the carb.

Disconnect it and run premix, dude.

thanks and i did... before i even started it.... but i think i still ruined the cylinder. it was testing @ 150 lbs yesterday and today its down to 120 and wont start. im trying to find piston rings for the malossi kit now. i did something wrong somewhere. i had it pre mixed. and had the oil pump hooked up to start. im buying rings to try it again and if i still have no luck. she's getting parted out. and im going back to 4 strokes!!

15
General Discussion / Re: how do you check an oil pump?
« on: March 03, 2011, 08:39:35 PM »
Quote from: juice on March 03, 2011, 04:41:48 PM
209  SKU: 15100-GAK-9500
PUMP ASSY OIL is a saleable item. 1 $52.26                                                                                                                  If you suspect your oil pump is bad you could replace it . Stadium Yamaha .

thanks but i was wondering how to check it. i just went ahead and pre mixed. but now im having other problems

Pages: [1] 2 3 ... 10