Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ABslt

Pages: [1]
1
Agility 125 / Re: Is the stock carb jet to big for high alltitude
« on: May 12, 2010, 01:26:23 AM »
once scooter was warm, i had 125, psi, but now i think maybe i will upgrade the parts, i need to know if the 2009 has the gy6 and i was thinking 2k springs and, 11g rollers does that sound about right?

2
Agility 125 / Re: agility 125 CDI mod
« on: May 11, 2010, 09:52:44 PM »
Sorry to hijack but is my 09 agilty the gy6 motor and any one have a link or where to find the 2000 springs from

3
Agility 125 / Re: Is the stock carb jet to big for high alltitude
« on: May 02, 2010, 03:05:02 AM »
checked the plug, and it looks good nice brown color, did a compression test but it was stone cold and it was only 90 psi, seems kind of low, but that was before the valve adjustment, so will try again warm and after the valves, then i will check back, hopfully its back to 120, if not i guess time for a motor rebuild

4
Agility 125 / Re: Is the stock carb jet to big for high alltitude
« on: May 01, 2010, 03:58:14 PM »
well its got 2k km on it, when i got it i changed engine oil gear oil new plug, adjusted valves, checked tire pressure, the only thing i didnt check was the belt and rollers and so on. Or clean the carb, i was thinking with only 2k km, there shouldnt be problems there

5
Agility 125 / Re: Is the stock carb jet to big for high alltitude
« on: May 01, 2010, 06:42:21 AM »
i thought mabye the stock jet was too big for the elevation i am at, id say on flat ground it has about 85kph. Ill have to clean out the carb and give that a try. thanks

6
Agility 125 / Is the stock carb jet to big for high alltitude
« on: May 01, 2010, 01:25:16 AM »
I bought the scooter second hand, it was in a town from sea level. I live at 6,300 feet the 125 seems I bit  under powered. So is the jet two big, or should I be able to get away with adjusting the air screw

7
Agility 125 / Re: 09 Agility valve adjustment???'s
« on: April 30, 2010, 05:16:00 PM »
thank you very much!!!!!

8
Agility 125 / Re: 09 Agility valve adjustment???'s
« on: April 30, 2010, 05:02:29 PM »
almost but i would use the gauge i have that says .005 .127mm. or the one that says .004  .102mm

9
Agility 125 / Re: 09 Agility valve adjustment???'s
« on: April 30, 2010, 03:33:07 AM »
Ok sorry to be confusing, but i have a decent explantion. So it is on the 125cc but i pulled up this manual from a different topic on this fourm here is the link...Kymco Agility 125 Service Manual    So from this source page 34 says that the clearance is 0.12mm. Now on page 39 it says 0.04mm. Same manual. So thats where im getting confused. So you said the 0.12mm is correct, if thats right i need to take it apart again. thanks

10
Agility 125 / 09 Agility valve adjustment???'s
« on: April 29, 2010, 07:04:03 PM »
The manual calls for 0.04mm on the intake and exhaust, all my feller gauges have no such thing. they have .004 but thats inchs, and all the mm are more like .152 .203 .508 and so on, do i need to buy a new set off feller gauges or am i just reading them wrong. Its just turned 2k km, so thats the first check figured might as well. Thanks

Pages: [1]