Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 02 zx 50 s.f.

Pages: [1] 2 3 4
1
zx50 / Would this work ?
« on: October 08, 2012, 08:28:31 PM »
I think my oil pump is dead so I've heard of people grinding the teeh down so it won't spin I've put a bbk on and pre mix now so my question is why can I not just pull the shaft out and bolt it down with out it in there so there is nothing to move its grinding some where and it's loud and I think that is the cause and when I turn the fan/alt I can see oil comeing out the base of the pump

2
zx50 / Re: MHR bored and stroked
« on: May 29, 2012, 04:53:17 PM »
But wouldn't I be Runing to lean if I do some hard down jeting?

3
zx50 / Re: MHR bored and stroked
« on: May 29, 2012, 11:22:24 AM »
The piston is on tdc on the jug. But I am going to try to seal the manifold like you said. Idk got to make it work for now but I want to start saving for a 24mm it would be nice to have both low and top but I was looking for top when I bought the kit. As long as I am not doing a 10 mph till 20 or 30.

4
zx50 / Re: MHR bored and stroked
« on: May 28, 2012, 11:44:49 AM »
Idk about anything bigger than a 24mm because the 30mm I just bought is becomeing a huge problem it's just toooooooo big I'm going to put a filter on to try to slow the flow down but it's huge I thought it would be good 90cc kit I just installed but we shall see oh and z how much for you to come and tune this beast hahaha if I had a boat I would have loaded that bitch up and been on my way to you you are just around the bend.

5
zx50 / What do I do ?
« on: May 20, 2012, 06:48:12 PM »
Ok first let me thank z he has been a huge help for me. Now I have orderd the 30 mm carb new intake manifold but it has no spot to put the vacume line for the petcok what do I do?

6
zx50 / Re: Everyone's comment
« on: April 22, 2012, 02:56:41 PM »
And that is the kit they are selling ?

7
zx50 / Re: Everyone's comment
« on: April 22, 2012, 01:33:36 PM »
I rember hearing people on here say that it ran but died very soon it's only 64 for a 70cc idk.

8
zx50 / Re: zx50 super fever problem?
« on: April 22, 2012, 01:29:57 PM »
It's probley the cdi mine was doing that too then it just blew.

9
zx50 / Everyone's comment
« on: April 22, 2012, 01:21:44 PM »
Scooter assigns bbk is it worth your Time

10
zx50 / Re: WTF ?????????????????
« on: April 18, 2012, 12:22:56 PM »
I would rather give you my cell because I'm using a IPhone as a computer and it sucks because the letters are small but if your cool talking I'll give you my num

11
zx50 / Re: WTF ?????????????????
« on: April 17, 2012, 11:20:13 AM »
I'm going to take the case apart today I need to get the alum chunks out but the crank looks good along with the rod. Your a life saver with the bbk I've been looking all over the web but none say for zx I have been scared to order it and it not fit I've heard of the zx and dio kits are a hit or miss. Do I have a af18 and am I a zx , zx 2 I have seen a lot of zx's but not like mine it has the zx supper fever little sticker on both sides and in the front as others they have a huge sticker

12
zx50 / Re: WTF ?????????????????
« on: April 17, 2012, 12:55:03 AM »
So yes it is and it turns out I blew a hole in the piston today I dont know why though but it is right under the spark plug.

13
zx50 / Re: WTF ?????????????????
« on: April 15, 2012, 04:01:29 PM »
Are you talking about the idel screw or the needle it's self is adjustable

14
zx50 / Re: WTF ?????????????????
« on: April 14, 2012, 01:47:50 PM »
So I just took the oil injection out and the o ring was good so I bent the tab that holds it down and it helped a lot but it's still funny with 7 gram rollers it's nice off the line but around 35 - 42 it's laging and then it takes off to aroun 55  once again that is what the tack says but I think it's 10% out or higher

15
zx50 / Re: WTF ?????????????????
« on: April 13, 2012, 12:01:58 PM »
Ok so I'm judging it's off on the speedo but I'm maxed at 50-55 on my speedo

Pages: [1] 2 3 4