Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SIG4EVA

Pages: [1]
1
Agility 50 / Aftermarket Exhaust Needed
« on: September 05, 2023, 08:15:15 PM »
I have a 2014 Kymco Agility 50 4T.
With a 100c bbk, 18mm carb 90 main 33 idle jet, 7/8" hogged intake, 1000 clutch springs, and stock contract spring, the best I've seen is 35mph flat and 40mph down hill.

Do you think exhaust is my restriction at this point?

2
Agility 50 / Upgraded Brake Light/Turn Signals
« on: August 16, 2023, 02:38:06 PM »
Have you guys found a good solution to replace the stock stuff? The previous owner destroyed the turn signal mounts so they are flopping around. Would be nice to have a LED retrofit or something all in one.

3
Agility 50 / Re: 2014 Agility 50 Big Bore Kit Install tips
« on: August 16, 2023, 02:00:27 PM »
For those that encounter the same issues, it was a bad carb out of the box. I took my old carb with a 78 jet and it was lean bogging and hot. Threw in the 85 jet this morning and she pulled 43 mph on partial throttle. I'm excited to see what she does after breakin and some Brotella T6 15W40.

4
Agility 50 / Re: 2014 Agility 50 Big Bore Kit Install tips
« on: August 15, 2023, 07:57:54 PM »
She idles great and great at 0-25% throttle. I started with a 90 jet, but it was bogging. Went to 85 and and it got a little better. Went to 80, thought it was good but now its doing this. Any feedback on which way I need to go either lower or higher?


*UPDATE* Pulled the intake pipe off at the carb and she ran great, no issues with heavy throttle. That would indicate its still too rich but with a BBK I thought it would still need a decent amount more fuel. Going back to the 78 and see if that helps.

5
Agility 50 / Re: 2014 Agility 50 Big Bore Kit Install tips
« on: August 15, 2023, 07:01:48 PM »
Quote from: Stig / Major Tom on August 14, 2023, 11:34:03 PM
Cool video!
This will be fun to follow!

Thanks for sharing
Stig

I forget, did we welcome you to the forum?

Thanks and appreciate the welcome! I got her all back together, she idles perfectly fine but I can't get it to run at high throttle. I have a smooth variator boss. Stock intake/exhaust. I started with the 90 jet and she sputtered and didn't want to run, died with throttle. Changed to the 85 and it started up much easier and idled perfect. But, still bogging with throttle. Should I jump down to 80 and see how it does? Any recommendations on tuning? I'm thinking since the exhaust/intake is stock, I don't need as much fuel as those running a cone filter and aftermarket exhast.

6
Agility 50 / Re: 2014 Agility 50 Big Bore Kit Install tips
« on: August 14, 2023, 02:49:22 PM »
Quote from: lukelaw1 on August 10, 2023, 12:42:00 AM
Following, I have a 2020 Kymco agility 50 and also bought a 50mm kit with head. Keep us updated!

Thanks! Did most of the swap yesterday. About 9:30PM last night, I realized I lost my feel gauge so I had to grab another one today. I need to check valve lash and then start putting her back together. I also have an electrical drain and bad wiring on the rear right blinker that I need to locate before the fairings go back on.

Quick video showing the build and size comparison.
https://youtube.com/shorts/9z9RXtucLXI?feature=share

7
Agility 50 / Re: 2014 Agility 50 Big Bore Kit Install tips
« on: August 07, 2023, 08:25:37 PM »
Quote from: Neil955i on July 25, 2023, 07:16:21 PM
Good luck with the project!

Thank you! Going to start the tear down this weekend.

8
Agility 50 / Re: 2014 Agility 50 Big Bore Kit Install tips
« on: July 25, 2023, 01:49:32 PM »
Now I am ready for fun activities.

Here's the 50mm big bore kit and 20mm upgraded carb.



9
Agility 50 / 2014 Agility 50 Big Bore Kit Install tips
« on: July 21, 2023, 07:28:15 PM »
Hey guys, after enjoying the scooter derestricted for over a year, its time to add some power. I was able to hit 38ish mph which is great, but our main road is 40 and people drive 40-60 mph.

I have the 50mm big bore kit that I will be installing. Do you guys have any tips or tricks for the install? I know longevity may take a hit but I'm prepared for that.
https://www.amazon.com/gp/product/B01303YV08/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Also, I was thinking of pairing it with this carb. The chinese replacement that was on mine bog at WOT and has idle issues, so I'd rather get a new one.
https://www.amazon.com/Glixal-ATMT1-073-1-Carburetor-Electric-Chinese/dp/B01EWHUHMM/ref=sr_1_2?crid=P7STI2YNYDAI&keywords=gy6%2Bcarburetor%2B100cc&qid=1689964100&sprefix=gy6%2Bcarburetor%2B100cc%2Caps%2C91&sr=8-2&th=1

Looking for any recommendations or useful tips before I start tearing her apart. Thanks!

10
Agility 50 / Metallic rattle coming from CVT
« on: June 15, 2022, 06:07:43 PM »
Hi guys, I just bought a 2014 Agility 50. The scooter has been awesome. I bought a variator and derestrict drive boss and installed them. Now I have a metal rattle that seems to be coming from the CVT area. It doesn't happen under partial throttle. I know everything has been torqued properly. It seems to happen under full throttle but it's intermittent. Do you guys have any ideas? Also, I found this washer, I'm not sure if it was already in the driveway or came from the scooter. The scooter drives totally fine.






Pages: [1]