Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - East Valley Scooters

Pages: [1]
1
Technical | How To / Sold my like200i. Parts leftover.
« on: February 03, 2024, 12:40:11 AM »
Hey all, 
Since I’ve sold my like200i, I’m left with 2 parts bikes. One is stripped to the frame, the second is non running and missing some cosmetic parts but, could be a good project bike.  What should I do with them?
I’ll post pics if anyone is interested.

2
LIKE 200i / Re: Need help finding Mass airflow sensor for 2011 Like 200i
« on: February 02, 2024, 02:08:57 AM »
Be careful if you unplug the throttle body. The pins inside the plug are very easy to bend over if you don’t line them up just right. I had my scooter for a very long and frustrating period before I realized that a few of the pins had been bent over inside the plug.  I was very lucky to be able to straighten them up again with a hook tool.

3
LIKE 200i / Re: No spray from the injector.
« on: May 17, 2023, 01:46:06 AM »
Thanks for the replies.
I got it running.
This Like came to me with a broken engine so I swapped in a motor from a parts bike.
Turns out I needed the throttle body from the original body, not the donor bike. I also had a flattened pin in the harness. I was able to straighten it out with a set of picks from harbor freight.
So it runs, with a sputter around 40mph and it won’t start without a jump. New battery is on the way. Hoping that takes care of that.

Thanks again,

Aaron

PS. I have some parts I don’t need.

4
LIKE 200i / Re: No spray from the injector.
« on: April 17, 2023, 07:55:09 AM »
Thanks for the replies.
Is there a way to test the current flowing to the electrical connector?
If I use a multimeter, how should I test and what should the readings be?

5
LIKE 200i / Re: Newbie needs some help - Kymco Like 200i Parts and questions - Please :-)
« on: April 13, 2023, 05:39:21 PM »
Hi and welcome.
I’m also new to the forum.
I have a parts bike if you need anything from it.

Aaron

6
LIKE 200i / Re: No spray from the injector.
« on: April 13, 2023, 05:35:42 PM »
Thanks so much for the responses.
I soaked the fuel injector in sea foam for a couple of days.
Then I hooked up a 12v battery to the terminals and sprayed carb cleaner through the injector.
It sprays well. However, when reassembled, the injector doesn’t spray.
There’s definitely pressure but the injector doesn’t seem to be opening.
Is there a way to test?
Btw, the fuel pump doesn’t come on unless I bypass the fuel pump relay.
I bought a new relay but, it doesn’t activate the pump.

Thanks again,
Aaron

7
LIKE 200i / Re: No spray from the injector.
« on: March 29, 2023, 01:40:02 AM »
Thanks for the responses.
I disconnected the fuel line from the injector. Turned the key and fuel flows.
I applied compressed air to the injector side. No air came out the other side.
I applied 12v to the terminals on the injector then, tried to blow air through from the injector side.
A small amount of air came through.
I’d like to try and clear the injector.
Any advice is appreciated.

Thanks

8
LIKE 200i / No spray from the injector.
« on: March 27, 2023, 10:45:44 PM »
I appreciate any help I can get with this.
I replaced the fuel pump and it is working.
I have replaced the short hose on top of the pump as well.
When the pump is activated, fuel sprays back into the tank through the valve just over the pump in the center of the pump housing. I’ve replaced the tip sensor and the fuel pump relay.
I don’t know what else to do. Please help.
Why does the fuel spray back into the tank?

Thanks
Aaron

Pages: [1]