1
Agility 50 / Re: Broken key, need new lock set?
« on: July 29, 2011, 12:17:39 PM »
I don't have an answer for you but, what are you going to do about the gas tank cap?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Agility 50 / Re: How to cut the cdi
« on: June 08, 2011, 06:11:40 PM »
I just cut the CDI wire on my 2006 Agility 50 two hours ago. 15 seconds with a hacksaw and it was done. I had to dig into the cut a bit to see that I actually cut a wire. Picked up about 6-7 MPH on a straight, flat street. Now does 40 MPH with no other modifications.
3
Downtown 300 / Acceleration
« on: June 08, 2011, 01:32:41 AM »
I have been considering buying a Downtown 300, especially after seeing one parked on the street in Annapolis last night. I have a Agility 50 which I use to get around town, other than that I've alway been a motorcycle person. I've owned many cycles up to 1000 cc. In my mind I'm trying to do a comparison of the acceleration of a Downtown 300 compared to a 300 cc motorcyle. I've not been able to find any reviews listing the typical 0 - 60 mph time for a Downtown 300. I love the rush that comes with a motorcyces's acceleration so I don't thing I'd be happy with something that couldn't beat your typical car in a streetlight to streetlight race. So does anyone have the data I'm looking for?
4
Agility 50 / Stalling
« on: June 03, 2011, 12:47:21 PM »
My 2006 Agility 50 starts immediately when I hit the start button and runs just fine at first. When I drive down the street it stalls at every stop sign for a couple of miles. Then it runs just fine. It is acting as if the electric choke was cutting off before the scooter engine is really warm. It has a new carb. on it with a new choke. To test the new choke I switched the electric choke unit from another scooter that I know is good and it makes no difference. So it is not the carb. or choke. I don't know how it ran before I replaced the carb. as it didn't run at all when I got it.
5
Agility 50 / Re: Exhaust system question
« on: May 19, 2011, 01:24:52 PM »
I threaded a 6 mm bolt into it. Quieter now.
6
Agility 50 / Re: Exhaust system question
« on: May 19, 2011, 01:37:18 AM »
I don't know the ID, but the OD is about 3/4 inch, I.E about the same diameter as the exhaust pipe.
7
Agility 50 / Exhaust system question
« on: May 19, 2011, 01:11:03 AM »
My 2006 Agility 50 has a "tee/open port" in the exhaust pipe a several inches before the muffler. The majority of the exhaust noise comes from this opening. when I put my foot over it the scooter gets much quieter. What is the purpose of this opening?
8
Agility 50 / Re: Agility 50 idles, but won't run
« on: May 19, 2011, 01:04:13 AM »
Ok, so draw jet is the main jet. Thanks. I'll remove carb. and clean jets again, and clean accelerator jump and lube linkage, springs, etc. I can't tell if it backfires as I can't get it above idle or it dies.
9
Agility 50 / Re: Agility 50 idles, but won't run
« on: May 18, 2011, 11:14:42 PM »
bthmteck, I cleaned all the jets with cleaner and compressed air, but tomorrow I'll remove the carb to clean the accelerator pump. You refere to a "draw jet". This is a term I'm not familiar with, which jet is this?
10
Agility 50 / Agility 50 idles, but won't run
« on: May 18, 2011, 10:03:28 PM »
I got a 2006 Agility 50 that had not been run in about two years. It had no key so I had to rig up a jumper to simulate the ignition switch. I first it would crank but not fire up. I then cleaned out the fuel tank, removed and cleaned the carb., replaced the spark plug, changed the oil, and put a good battery in it. Now it fires up and idles just fine. The problem is the as soon as I open the throttle, even when the engine is warm, it dies immediately. The only thing I didn't dismantle and clean on the carb. was the accelerator pump( I forgot to do this and didn't remember until I had it reinstalled). Could this be the source of the problem or is there something else I overlooked?
11
Agility 50 / Ingition Switch wiring
« on: May 15, 2011, 10:14:55 PM »
Somebody gave me a 2006 Agility 50. There is no key or manual with it. It has not been run in a least two years. Before I invest in a new ignition switch and battery I want to see if it will start. To do this I need to simulate the operation of the ignition switch using jumper wires. The current switch has five wires coming off of it. A red, a black, two green and one black with white tracer. The red, black, and green go to a six position white plastic connector, of which only four are used. The black with white does not go to this connector, but to a separate plug. This separate female plug that this black/white wire plugs into has a blue wire with yallow tracer on it. I have a battery I'm going to take out of another scooter I have to power this test.
Also, is ther anything else I should do besides changing the fuel and checking the oil?
Also, is ther anything else I should do besides changing the fuel and checking the oil?
Pages: [1]