Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sthomas904

Pages: [1] 2
1
zx50 / Re: no lights what so ever
« on: September 27, 2009, 12:54:07 PM »
well the gas gauge works now.. but the headlights,brake,turn doesn't, i checked the voltage regulator and checked for voltage going to it, but i could find any voltage going to it, ill check the ground and i am going to borrow a multimeter from my neighbor and see if i get different results

2
zx50 / no lights what so ever
« on: September 24, 2009, 01:16:18 AM »
no lights, speed gauge works, but not the gas any thoughts?

3
zx50 / Re: Wheel runs in reverse!
« on: September 24, 2009, 01:13:33 AM »
mine did that once, but it quit doing it when i changed the flywheel, also do you happen to have a aftermarket cdi?

4
Technical | How To / Re: idles but wont respond
« on: September 23, 2009, 03:46:21 PM »
Figured it out!! flywheel was so rusted iy was preventing from starting/running right

I know its an old post but i figured i would post my results

5
Technical | How To / Re: idles but wont respond
« on: April 09, 2009, 04:07:11 PM »
well i got the new cdi, but i took apart the cylinder head and noticed the metal gasket was bent and had been leaking a little gas out the back corner of the motor, i used the metal gasket and some rtv so hopefully this will fix my problem  ;D

6
Technical | How To / Re: idles but wont respond
« on: March 23, 2009, 04:40:40 PM »
well i ordered a new cdi a couple of days ago, i should receive it this week and I will let you know if its fixed

7
Technical | How To / Re: idles but wont respond
« on: March 19, 2009, 11:05:48 PM »
ok i replaced the autocock,fuel line fuel filter and ignition coil.cleaned the fuel tank out. it ran for a little bit then at about 30mph it quit responding and shut down, would the cdi have anything to do with this? I was told by a parts guy that this particular scooter always had problems with these. its a 2000 kymco zx50 2stroke

8
Technical | How To / Re: idles but wont respond
« on: March 15, 2009, 04:08:14 PM »
well i found out somthing interesting today... with the kill switch on it cranks and runs but when you give it gas, nothing. with the kill switch in the off position it runs somewhat like it should  >:(  i posted a video 

9
Technical | How To / Re: idles but wont respond
« on: March 11, 2009, 11:33:43 PM »
well today i took the intake off and behold someone used rtv stuff to make a gasket, now i know you can do that with antifreeze and oil but gas  ??? i dont know

10
Technical | How To / idles but wont respond
« on: March 11, 2009, 12:05:38 AM »
engine idles and when I give it gas it doesn't respond  ??? i checked the throttle cable and its working its like the gas just wont go into the intake any thoughts? 

11
Technical | How To / Re: super fever ZX50 carb overflow
« on: March 02, 2009, 10:32:18 PM »
now im thinking it is the ignition coil. on the Resistance test i am getting .009 not the .153 to .187 there is spark and it shocked me the other day ??? but nothing like it should have

12
Technical | How To / Re: super fever ZX50 carb overflow
« on: February 25, 2009, 08:02:37 PM »
its the part that comes off the oil pump going to the carb. now does it inject it into the carb? I also found a place where it says its a 32-1 mix. if they jost sold that one piece instaed of buying the whole pump i would be happy

13
Technical | How To / Re: super fever ZX50 carb overflow
« on: February 25, 2009, 12:18:39 PM »
before i forget, i forgot to tell you i was premixing the fuel, do you think that has something to do with it?

I broke off the fitting that goes to the carb some how.


14
Technical | How To / Re: super fever ZX50 carb overflow
« on: February 23, 2009, 11:52:28 PM »
now im having problems again, it will start up for a second or two and shut off, would i be better off to get a new carb and if so where are they the cheapest to get?

15
Technical | How To / Re: super fever ZX50 carb overflow
« on: February 20, 2009, 01:35:42 AM »
thank you that helped!!!!!!!!!!!!!!!!

Pages: [1] 2