1
Agility 50 / Re: New to Kymco just got 2013 AG50
« on: August 22, 2013, 05:20:54 AM »
I have a 2013 and I cut the Cdi box little green wire it was restricted
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Agility 50 / Re: 2013 Agility Derestriction
« on: June 29, 2013, 02:30:58 AM »
Good to know I have the same warranty!!!
3
Agility 50 / Re: 2013 Agility Derestriction
« on: June 27, 2013, 01:19:22 AM »
My 2013 I cut CDI, 82 main jet, 1500 contra spring 5.5 roller weight, 1500 clutch springs it runs pretty good before that it ran like dog crap!
4
Agility 50 / Re: 1500 torque spring 2000 clutch springs 5.5 roller weights??
« on: May 22, 2013, 11:36:53 PM »
Thanks! I'm climbing hills way faster and a lot mor torque off the start. I lost 3 mph on the flats but gained 5 on the Down hill! Pretty awesome!
5
Agility 50 / 1500 torque spring 2000 clutch springs 5.5 roller weights??
« on: May 22, 2013, 07:54:45 AM »
I put in 1500 torque spring 2000 clutch springs 5.5 roller weights?? Is the 2000 rpm clutch springs to much???
6
Agility 50 / Re: 1500 torque spring length and problems!!
« on: May 20, 2013, 02:55:06 AM »
Thanks I put on the belt before putting the clutch back on the bike!
7
Agility 50 / Re: 1500 torque spring length and problems!!
« on: May 17, 2013, 06:57:22 AM »
Yea called my dealership and asked they said 4 in shouldn't be a problem! They said get a friend to help put the belt on why I hold it open! It isn't stuck but can't believe how hard it is to pull back the plate every fits fine. My scoot only has 2300 km on it and is brand new but am going to degrease and put some new grease! This is the spring I purchased http://www.racingplanetusa.com/torque-springs-naraku-sport-single-p-136439-1.html?cPath=2_15382_15386&sessID=00cbafe583fdb43956708df085342cc8
8
Agility 50 / Re: Source for jets in USA
« on: May 17, 2013, 02:05:37 AM »
Maybe I put an 82 main jet in my stock motor it runs better. Just call and ask!
9
Agility 50 / Re: Source for jets in USA
« on: May 16, 2013, 10:58:45 PM »
I don't know I'm in Vegas and just buy them from the dealer!
10
Agility 50 / 1500 torque spring length and problems!!
« on: May 16, 2013, 10:57:11 PM »
I just purchased a 1500 naraku torque spring and went to install and can't get the belt back on! So I took it back off and measured the new spring from the stock and the new one is 4in and the old one 3 and 5/8! Is this a problem it said it was for a kymco 50. Also I went and put the origanal back on and it was extremely hard to get the belt back on!
12
Agility 50 / Re: CDI Modification
« on: May 16, 2013, 04:15:48 AM »
Cut CDI just did mine got 5-7 mph out of it!
13
Agility 50 / Re: 2013 CDI box cut and it was a succes!!!!
« on: May 12, 2013, 04:29:43 AM »
Yes there is still a little green wire on the bottem right half way in to the box! I just used a hack saw. I got 5-7 mph faster! Awesome still slow up hill though!
14
Agility 50 / Roller weight size 16/13 is correct yes or no?
« on: May 03, 2013, 02:10:13 AM »
I'm ordering roller weights is 16/13 correct?
15
Agility 50 / 2013 CDI box cut and it was a succes!!!!
« on: May 03, 2013, 02:09:01 AM »
2013 CDI are restrictid I cut the right corner until I hit the little green wire!! Thanks to the right up on the forum! Got 5-7 MPH faster!