1
Super 8 150 / Re: shop/service manual ?
« on: May 06, 2013, 08:05:45 PM »
Look up cyclepedia on the net , they have one online , for a subscription price ofcourse , I got one , it's been quite helpful.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Super 8 150 / Re: How much do rollers weigh super 8 150
« on: May 06, 2013, 08:03:37 PM »
When changing the roller weights , they all have to be positioned the same way , with the overlay to the right , if you look closely at them you will notice it , look on you tube they have a video post , visually showing what I mean , otherwise you will get the noise / vibration etc as you described , and possibly do some engine damage.
3
Super 8 150 / Re: Engine: Repair or replace?
« on: May 06, 2013, 07:48:56 PM »
The problem with replacing the motor , is that the distance between the engine and the rear axle differs , the ads you see on the net , are traditional for long and short case motors , but , where the super 8 has 14" wheels ,the distance between is greater ; so the dealer would be right from that point of view.
4
Super 8 150 / Re: Gear oil puking into airbox
« on: May 06, 2013, 07:29:47 PM »
Gear oil level is .18 L , very easy to remedy , look on youtube , there is a video on it , that's how I know .
Check cyclepedia , they have online Full Service Manuels , for Purchase , I bought a subscription off of them.
Hope this helps''.
Check cyclepedia , they have online Full Service Manuels , for Purchase , I bought a subscription off of them.
Hope this helps''.
5
Super 8 150 / Correction
« on: May 06, 2013, 07:22:30 PM »
What Works : Yoshimura 1590075 TRC SS Exhaust , NCY Super Variator Transmission Set , Malossi X Aramid ( Kevlar ) CVT Belt , Naraku NK 600.03F 160cc Block , NCY Cold Air Intake , Opticparts DF Checkered Aluminum Foot Plate # 21714 , Naraku NK900.78 2000 RPM Clutch Springs , Naraku NK900.76 2000 RPM Torque Spring, OKO K-301 CVK 30mm Carburetor , NCY Intake ( 2 Vacuum Ports ), K&N RX-4010 Air Filter ( For NCY Cold-Air Intake ), K&N 62-1000 Vent Filters x2 , 18x14x12.10g Naraku Rollers NK918.121
What DOESN"T Work : Naraku NK600.38 Cylinder Head , Naraku NK390.34 CDI ( Unless the one I received was Faulty ) , Composimo GY6 Anklebiter CVT Cover
Just FYI , trying to save you some money ( Where I Lost Some ) , incase you were thinking about similar upgrades".
I ran my Super 8 , to 120 km (75mph) , Yesterday on a Flat Straight Away , with said upgrades.
P.S. 1) Has anybody used the same CDI as I have ,and if so , did you experience any Problems? Or can you recommend one ? I would like a Plug and Play version preferably ''.
2) What Performance head will work on the Super 8 150 , and do you need to change the timing chain to a different length , I am looking for a bolt on , and rather not have to split the engine''.
CORRECTION: After a lot of trial and error , you can get the Naraku head to work , you have to get a 45 link timing chain , and the A14 cam will work with this set up , and the Naraku cdi is needed for this setup as the original one will no longer function properly... Having said that you also have to modify the flange on the Yosh. exhaust as the flange will be needed to be rotated , where the head is shorter...Boy amazing difference with my setup now , she is soo punchy now , I'm a happy Camper
What DOESN"T Work : Naraku NK600.38 Cylinder Head , Naraku NK390.34 CDI ( Unless the one I received was Faulty ) , Composimo GY6 Anklebiter CVT Cover
Just FYI , trying to save you some money ( Where I Lost Some ) , incase you were thinking about similar upgrades".
I ran my Super 8 , to 120 km (75mph) , Yesterday on a Flat Straight Away , with said upgrades.
P.S. 1) Has anybody used the same CDI as I have ,and if so , did you experience any Problems? Or can you recommend one ? I would like a Plug and Play version preferably ''.
2) What Performance head will work on the Super 8 150 , and do you need to change the timing chain to a different length , I am looking for a bolt on , and rather not have to split the engine''.
CORRECTION: After a lot of trial and error , you can get the Naraku head to work , you have to get a 45 link timing chain , and the A14 cam will work with this set up , and the Naraku cdi is needed for this setup as the original one will no longer function properly... Having said that you also have to modify the flange on the Yosh. exhaust as the flange will be needed to be rotated , where the head is shorter...Boy amazing difference with my setup now , she is soo punchy now , I'm a happy Camper
Pages: [1]