Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 06_typeS

Pages: [1]
1
zx50 / Technigas Type R results
« on: September 07, 2015, 06:36:45 PM »
so I recently installed my new exhaust, pod filter and swapped out my main jet. Stock was a #80, started with a #96,  didn't run well. Down to a #94, still didn't run well.  I'm down to a 92 or 90 now, I can't re,ever. Seems to run fine. Much better acceleration from 0-30kmh, then hits a wall from 30-40kmh,  but pulls hard and strong from 40-70. 

I had to readjust the carb due to idling issues. But I'm having a hard time with the main jet.  Is their a sweet spot?  So many turns out after screwing it fully in?  Is 70kmh on a flat hill my max speed?

Mods are aftermarket cdi, exhaust, filter, jet and spacer removed from transmission.

Thanks for the help fellow scoots.

2
People 50 / Re: GS1 motor
« on: September 06, 2015, 06:00:26 PM »
recently purchased a Techigas Type R exhaust, uni filter, and various sizes of jets. Stock is #85, decided to start at #96 and work my way down. After install took it for a drive. Great low end torque but lacked at top speed. Started to bog out between 60-70km/h

Checked up for a #94. Then for some reason it wound let start until I applied throttle. Had to play around with carb screws to get the idle up. Took it for,a spin, seemed slower. 

Anyone wanna let me know what size jet would be good for intake and exhaust? 

3
People 50 / Re: GS1 motor
« on: August 25, 2015, 05:44:24 AM »
Well  bit of an update. 

I tore the Carb apart and cleaned it out well, re-assembled and the scoot started right back up.  Let it warm up and applied throttle, was about 75% when I noticed the miss was still there. 

So I went to remove the plug again.  upon removal of the coil, it snapped off.   So I was sure that that was causing my miss.

I had to wait the rest of the weekend before going in yesterday for a new top, installed it.  Started right up, took her for a drive and topped out at about 78 km/h with no miss.

Yay me, lol

4
People 50 / Re: GS1 motor
« on: August 19, 2015, 10:56:01 AM »
Awesome, thats great.  I really appreciate the help.  Looked up Honda Gio parts and I got a bit excited, ha

The Scoots been running rough as of late. 

Long story short, I dropped the bike going around a traffic circle going like 5 km/h, rear wheel spun out in a rain storm and I did a 180*turn and laid it on its side.  Quickly picked it up but it hasent run right since then.  bought a new plug, new gas.  After I put the plug in drove it a few KMs and thought it was fine, restarted it 5 days later and it shut off on me as I left the driveway.  Regapped the plug from .06mm to .07mm and it runs great until about 60-70km/h the spits and sputter, also at idle it seems to run rough. 

I dropped by my local Kymco dealer and he told me to try and clean out the carb and it should fix my problem. 

Hopefully that will work, so I can begin the mods. ;D

5
People 50 / Re: GS1 motor
« on: August 18, 2015, 08:23:45 AM »
I also found Kymco SC10AS, but still nothing much comes up on a search.

6
People 50 / Re: GS1 motor
« on: August 18, 2015, 06:16:19 AM »
Another Pic.

7
People 50 / Re: GS1 motor
« on: August 18, 2015, 06:10:29 AM »
Quote from: BettinANDlosing on August 18, 2015, 02:03:29 AM
You sure it's a kymco? Never ever heard of the gs1.

Quite positive, lol.


8
People 50 / GS1 motor
« on: August 17, 2015, 08:38:53 PM »
Hello everyone,

First time poster, long time lurker.

I recently had to do some maintenance to my KB 50 Meteorite and pondered the idea of a 150cc swap. After a lot of searching I managed to find that this scooter has the GS1 motor. Can anyone tell me f it is a variant or similar to a GY6?

Would a GY6 swap in with minimal to no problems?  I'm quite sure that my GS1 is a short case as I have a 12" tire.

Can anyone recommend me to a page or a site to do more research?

Any help is appreciated.

Thanks.

Pics for attention.

Pages: [1]