« previous next »
Pages: [1] 2

Author Topic: restriction problem  (Read 4358 times)

franx93

  • Newbie
  • *
  • Posts: 41
    • View Profile
restriction problem
« on: September 08, 2009, 10:15:11 PM »
hello....on my agility 2008 R16 i put an unrestricted boss, cut violet wire, and put #82 main jet...but it goes only 55 km/h. if i plug half air hole behind the filter it goes 62/63km/h, but some friends go 65km/h plugging nothing. is there any other adjustament to do at the carburator?
thank you for your time :)
« Last Edit: September 09, 2009, 12:11:58 AM by franx93 »
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #1 on: September 09, 2009, 10:21:29 AM »
Quote from: franx93 on September 08, 2009, 10:15:11 PM
hello....on my agility 2008 R16 i put an unrestricted boss, cut violet wire, and put #82 main jet...but it goes only 55 km/h. if i plug half air hole behind the filter it goes 62/63km/h, but some friends go 65km/h plugging nothing. is there any other adjustament to do at the carburator?
thank you for your time :)

..i thought the wire was green......hmmm...

..try an 85 jet..you may be running lean...

peace
Logged
..every mod (action) necessitates a (reaction) mod..

franx93

  • Newbie
  • *
  • Posts: 41
    • View Profile
Re: restriction problem
« Reply #2 on: September 09, 2009, 10:30:13 AM »
i tried an 86 jet...it runs better but doesn't go 65 km/h...i don't know why...:( the carburator is also clean
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #3 on: September 09, 2009, 10:32:29 AM »
..where did you cut this violet wire??
Logged
..every mod (action) necessitates a (reaction) mod..

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #4 on: September 09, 2009, 10:38:51 AM »
...this is where you should cut..
Logged
..every mod (action) necessitates a (reaction) mod..

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #5 on: September 09, 2009, 10:43:44 AM »
..my dealer did this..
Logged
..every mod (action) necessitates a (reaction) mod..

franx93

  • Newbie
  • *
  • Posts: 41
    • View Profile
Re: restriction problem
« Reply #6 on: September 09, 2009, 11:18:32 AM »
my cdi is not this. is original r16 cdi...and the restriction go out cutting violet wires..
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #7 on: September 09, 2009, 11:49:07 AM »
..this is my original Agility 50 cdi...

..what scooter do you have??
Logged
..every mod (action) necessitates a (reaction) mod..

Kenho21

  • Sr. Member
  • ****
  • Posts: 418
  • I live my life 0.402336 kilometers at a time
    • View Profile
Re: restriction problem
« Reply #8 on: September 09, 2009, 12:19:45 PM »
I adjusted the engine size, lol

Ken
Logged
2009 Kymco Agility 50- 72cc Airsal kit, Uni Free-Flow Air Filter, Main Jet 120, 1500 Contra Spring, 6g Rollers, Malossi Multivar Variator, NCY Exhaust, NCY 80cc Camshaft, Cut CDI, Smooth Boss Drive, MRP Ignition Coil

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #9 on: September 09, 2009, 12:20:58 PM »
Quote from: Kenho21 on September 09, 2009, 12:19:45 PM
I adjusted the engine size, lol

Ken

 :D ;D :o
Logged
..every mod (action) necessitates a (reaction) mod..

franx93

  • Newbie
  • *
  • Posts: 41
    • View Profile
Re: restriction problem
« Reply #10 on: September 09, 2009, 12:30:17 PM »
agility 2008...the problem is not the cdi, i'm sure...so, is there any adjustament to do at the carburator except main jet and needle jet? (#86 main jet and original needle jet.)
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #11 on: September 09, 2009, 12:41:52 PM »
Quote from: franx93 on September 09, 2009, 12:30:17 PM
agility 2008...the problem is not the cdi, i'm sure...so, is there any adjustament to do at the carburator except main jet and needle jet? (#86 main jet and original needle jet.)

..I bought my 08 Agility 50 new...These pics of the cdi are of STOCK cdi's...

..If you didn't cut as the pics are shown, then you may very well have a cdi problem...

..and no, there are no other carburetor adjustments to be made, that I know of...

..other than a "High flow" air intake filter, that may require some further carb tuning...


.....Anybody else agree with me??

..or have anything else to offer franx??

peace
Logged
..every mod (action) necessitates a (reaction) mod..

franx93

  • Newbie
  • *
  • Posts: 41
    • View Profile
Re: restriction problem
« Reply #12 on: September 09, 2009, 12:58:37 PM »
wordslinger mine is an R16 ;) yours is R12...cdi are different ;)
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #13 on: September 09, 2009, 01:22:56 PM »
Quote from: franx93 on September 09, 2009, 12:58:37 PM
wordslinger mine is an R16 ;) yours is R12...cdi are different ;)

..ok, yeah..i overlooked that...

..sounds like you have big problems then...

 ;D
Logged
..every mod (action) necessitates a (reaction) mod..

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: restriction problem
« Reply #14 on: September 09, 2009, 04:30:05 PM »
..franx..comparing the specs of the 2008 A50 r12 and the 2008 A50 r16...

..the A50 r12 has 3.5 horsepower..@ 7500rpm (restricted)
..the A50 r16 has 2.4 horsepower..@ 7500rpm (restricted)

..the A50 r12 weighs 92.5 kg (204 lbs)
..the A50 r16 weighs 100 kg (220.5 lbs)

Is this what your scoot looks like?

..trying to educate myself a bit..  ;)
« Last Edit: September 09, 2009, 04:39:19 PM by wordslinger »
Logged
..every mod (action) necessitates a (reaction) mod..

An Error Has Occurred!

Call to undefined function split()
Back