Author Topic: People 50 2t lacks power  (Read 2307 times)

blufx

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
People 50 2t lacks power
« on: September 03, 2015, 06:19:47 PM »
I recently got a 2000 People 50 2 cycle. It looks good and seems to run good, but 25-30 MPH is all it will do. I weigh in at 130lb. I pulled the cover and found the bushing on the variable pulley has been replaced with a smooth one. I removed the exhaust to remove the restricter washer, but there's not one in it. From what I've read, the way it is now, I ought to be getting 40mph. I think the CDI is stock, and I haven't taken the carb off to check jet sizes yet. I did measure the rollers in the variable pulley and found them to be bigger than stock. With this known info, what can I check and do to make it faster?
« Last Edit: September 06, 2015, 08:05:05 AM by blufx »
Looking back, when I said I wanted to be somebody, I should have been a lot more specific.

scooterdad2324

  • Full Member
  • ***
  • Posts: 112
    • View Profile
Re: People 50 2t lacks power
« Reply #1 on: September 03, 2015, 06:26:47 PM »
You can cut at the end of the cdi box with a hacksaw and cut deep enough until you see where you have cut a little copper wire. That's the rev limiter. It should touch close to 40 by doing that.

Sent from my XT1526 using Tapatalk


blufx

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
Re: People 50 2t lacks power
« Reply #2 on: September 03, 2015, 06:43:43 PM »
You can cut at the end of the cdi box with a hacksaw and cut deep enough until you see where you have cut a little copper wire. That's the rev limiter. It should touch close to 40 by doing that.

Sent from my XT1526 using Tapatalk

Thanks for that damn quick reply, scooterdad2324. I've seen a couple of pages covering this but wasn't clear if it was indeed for my CDI, and I couldn't make out how deep to cut. I know I'll see a copper wire, but at a 45 degree angle, do you have an approximate depth I need to go? I figure that will vary, it being resin filled, but do I need to worry about hitting anything else?
Looking back, when I said I wanted to be somebody, I should have been a lot more specific.

scooterdad2324

  • Full Member
  • ***
  • Posts: 112
    • View Profile
Re: People 50 2t lacks power
« Reply #3 on: September 03, 2015, 11:59:13 PM »
I cut mine only about an inch deep and you tube has some videos on this subject and I wouldn't think there is anything else in that area to worry about. But once again check the you tube video's. That's what I did before I cut into mine. Good luck and safe scooting my friend

Sent from my XT1526 using Tapatalk


blufx

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
Re: People 50 2t lacks power
« Reply #4 on: September 04, 2015, 05:20:45 PM »
I cut mine only about an inch deep and you tube has some videos on this subject and I wouldn't think there is anything else in that area to worry about. But once again check the you tube video's. That's what I did before I cut into mine. Good luck and safe scooting my friend

Sent from my XT1526 using Tapatalk

I watched a couple of videos. When I sawed into mine, I didn't find a wire. I found a coil. Of course, as soon as I hit it, it was ruined. I need to find a replacement CDI for a 2000 People 50 2 stroke, USA model. Where can I get one fast?
Looking back, when I said I wanted to be somebody, I should have been a lot more specific.

blufx

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
Re: People 50 2t lacks power
« Reply #5 on: September 04, 2015, 09:17:03 PM »
I watched a couple of videos. When I sawed into mine, I didn't find a wire. I found a coil. Of course, as soon as I hit it, it was ruined. I need to find a replacement CDI for a 2000 People 50 2 stroke, USA model. Where can I get one fast?

Going back and looking under bright light, I never knew I went through the wire. I destroyed it. Can't blame anyone else. But for future reference, DON"T go too deep! There is  a coil there, and if you touch it, you can toss that CDI and start over.
Looking back, when I said I wanted to be somebody, I should have been a lot more specific.

Chris0381

  • Hero Member
  • *****
  • Posts: 652
    • View Profile
Re: People 50 2t lacks power
« Reply #6 on: September 04, 2015, 09:27:42 PM »
Do a little searching, you may find a derestricted CDI replacement. I thought I saw some somewhere.
2013 Super 8 50cc 2T Air Cooled Mfg'd 2012
Stock pipe derestriction
Smooth Boss
6.5gm Dr Pulley sliders
Malossi Torsion Controller
Malossi Fly Clutch- yellow springs
Polini Variator
#95 Main Jet
Purple Malossi Contra Spring
42 MPH on the flats with the wind

Chris0381

  • Hero Member
  • *****
  • Posts: 652
    • View Profile
Re: People 50 2t lacks power
« Reply #7 on: September 06, 2015, 11:30:45 AM »
This is what I was referring to. Something like this.

http://www.ebay.com/itm/UNRESTRICTED-CDi-for-KYMCO-People-50cc-2-STROKE-Spacer-50cc-/181264909954

I'd contact Scooter Asassins and see what they can do so you dont have to be cutting a CDI again
2013 Super 8 50cc 2T Air Cooled Mfg'd 2012
Stock pipe derestriction
Smooth Boss
6.5gm Dr Pulley sliders
Malossi Torsion Controller
Malossi Fly Clutch- yellow springs
Polini Variator
#95 Main Jet
Purple Malossi Contra Spring
42 MPH on the flats with the wind

blufx

  • Jr. Member
  • **
  • Posts: 64
    • View Profile
Re: People 50 2t lacks power
« Reply #8 on: September 11, 2015, 02:16:27 AM »
This is what I was referring to. Something like this.

http://www.ebay.com/itm/UNRESTRICTED-CDi-for-KYMCO-People-50cc-2-STROKE-Spacer-50cc-/181264909954

I'd contact Scooter Asassins and see what they can do so you dont have to be cutting a CDI again

Thanks for the link, but I had already found that one. If you scroll down to the compatible list, the People 50 has great big letters saying, "not for USA or Canadain scooters".
Looking back, when I said I wanted to be somebody, I should have been a lot more specific.

Bravin Neff

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: People 50 2t lacks power
« Reply #9 on: September 25, 2015, 01:11:50 AM »
I have a hard time believing its the CDI box. In my experience, with a 2002 People 50 2T, between the variator pin and CDI box, the variator pin yielded far more speed gains than the CDI. I went from 26 mph to 45 mph (indicated) just from the variator pin, and the derestricted CDI box got me to 48-50. Something else is wrong.

An Error Has Occurred!

Call to undefined function split()