Author Topic: Is there a difference between Dt300 and gt 300 variator and clutch assembly  (Read 1761 times)

carmen007

  • Newbie
  • *
  • Posts: 33
    • View Profile
I was on the way home doing about 70. bike started to slow down. Got it home took the case off. and i saw this. (In pict) A little while      ago I got a replacement engine from the dealer. I realized that I got a Dt300 motor not a People 300 gti which i have. I replaced the dr pully 20x12 14g and sliders and belt. I noticed that i have lea7 and lea5 parts, Is there a difference in size in the parts that the belt was shredded. Where is the best place to get replacement parts?

thx 
2013 Kymco People GT 300I
14g Dr pulley

2009 Schwinn Newport 150
2012 Genuine Buddy 125

CROSSBOLT

  • Hero Member
  • *****
  • Posts: 7758
  • West Tennessee, USA
    • View Profile
Someone smarter than me on here said the engine-transmission units are the same except for the final gearing. That makes perfect manufacturing sense. I had a similar failure of belt in a DT300i caused by stopped air flow. Mice had packed birdseed in the CVT air inlet.
Karl

Three motorcycles 1960-1977 (restored a 1955 BSA)
Agility 50
Yager 200i
Downtown 300i
Navy tech, Ships Engineer, pilot and aircraft mechanic

agilebda

  • Sr. Member
  • ****
  • Posts: 408
    • View Profile
Yikes. Scarey. Is the variator still good?

carmen007

  • Newbie
  • *
  • Posts: 33
    • View Profile
Yikes. Scarey. Is the variator still good?
Not sure. Looking for replacement.

Sent from my SM-T380 using Tapatalk

2013 Kymco People GT 300I
14g Dr pulley

2009 Schwinn Newport 150
2012 Genuine Buddy 125

de dee

  • Hero Member
  • *****
  • Posts: 2055
  • 2011 300i downtown 82,265 KM.
    • View Profile
  it looks like the pulleys are to big for the frame that would not leave enough space for the belt to wobble, the sliders on the back of pulley broke from over torque as the pulley is on the boss with no power from crank shaft except from the sliders ,  and the outer pulley , lighter roller sliders might have worked  by not pushing the belt out to far,  I would have reved the motor with the tranny cover off , to see how it worked , before  riding it, hind site is always 20 / 20

Trucker jay

  • Jr. Member
  • **
  • Posts: 82
    • View Profile
Dang I just reread some of your old post man you been thru hell over this scoot.  Hope you get it sorted out and many happy miles on it.

de dee

  • Hero Member
  • *****
  • Posts: 2055
  • 2011 300i downtown 82,265 KM.
    • View Profile
reading again the sizes are the same but the ramp the slider rollers  go into are different, they will push the belt higher out,  I bought both variators to see what the difference was,. I was looking for lower RPM s for my downtown at speed,.  ended up I had to grind the downtown pulley ramps  to do that ,.  now malossi is doing that for lots of scooters,. 

Viper254

  • Hero Member
  • *****
  • Posts: 817
  • Moped Pirate
    • View Profile
I suspect the variator will be fine as long as the little bushes are replaced at the same time as the roller. It's what they're there to do - protect it from massive breakdowns like this!
Rides;

Suzuki GW250 Inazuma (2016)
Honda C70C (red, 1983)

An Error Has Occurred!

Call to undefined function split()