« previous next »
Pages: 1 [2]

Author Topic: Naraku Drive Belt  (Read 4919 times)

omfgdotcodotuk

  • Sr. Member
  • ****
  • Posts: 334
  • fookin quick gilera ice 50/70cc malossified ish
    • View Profile
Re: Naraku Drive Belt
« Reply #15 on: October 08, 2010, 12:42:10 AM »
Im gonna give it a try thats for sure ;)
Logged
Never ride faster than your guardian angel can fly ;)

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: Naraku Drive Belt
« Reply #16 on: October 08, 2010, 12:46:31 AM »
...SLIGHTLY!!!!...longer...

..like by 1/16th inch....
Logged
..every mod (action) necessitates a (reaction) mod..

omfgdotcodotuk

  • Sr. Member
  • ****
  • Posts: 334
  • fookin quick gilera ice 50/70cc malossified ish
    • View Profile
Re: Naraku Drive Belt
« Reply #17 on: October 08, 2010, 12:57:24 AM »
Belt research time,muchhhhhhhhhhhhhh ::)
Logged
Never ride faster than your guardian angel can fly ;)

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: Naraku Drive Belt
« Reply #18 on: October 08, 2010, 01:05:36 AM »
..yeah..a cpl mm here or there will GREATLY  affect cvt performance...
Logged
..every mod (action) necessitates a (reaction) mod..

blue

  • Hero Member
  • *****
  • Posts: 3935
    • View Profile
Re: Naraku Drive Belt
« Reply #19 on: October 08, 2010, 02:26:20 AM »
I have the kevlar belt put on last summer and stell good.I am thinking of trying a slight wider belt
for fast take off. thats if I can find one.
Logged

rliburd2002

  • Newbie
  • *
  • Posts: 21
    • View Profile
Re: Naraku Drive Belt
« Reply #20 on: October 09, 2010, 10:39:31 AM »
Yeah I had the problem with the belt leaving powder everywhere. I cleaned it up best I could without taking apart the clutch. I suppose I should do that!
I dont have the holding tool for the clutch. I might try and make one.
Logged

blue

  • Hero Member
  • *****
  • Posts: 3935
    • View Profile
Re: Naraku Drive Belt
« Reply #21 on: October 09, 2010, 12:48:09 PM »
Quote from: rliburd2002 on October 09, 2010, 10:39:31 AM
Yeah I had the problem with the belt leaving powder everywhere. I cleaned it up best I could without taking apart the clutch. I suppose I should do that!
I dont have the holding tool for the clutch. I might try and make one.
  check out the post on clutch tools there are a lot of ways with out makeing anything.
Logged

omfgdotcodotuk

  • Sr. Member
  • ****
  • Posts: 334
  • fookin quick gilera ice 50/70cc malossified ish
    • View Profile
Re: Naraku Drive Belt
« Reply #22 on: October 09, 2010, 06:00:07 PM »
check out the post on clutch tools there are a lot of ways with out makeing anything.
WHAT BLUE SAID ;D
« Last Edit: October 09, 2010, 06:01:49 PM by omfgdotcodotuk »
Logged
Never ride faster than your guardian angel can fly ;)

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: Naraku Drive Belt
« Reply #23 on: October 10, 2010, 01:44:32 AM »
I cleaned it up best I could without taking apart the clutch. I suppose I should do that!


..it's always good to keep your cvt bits nice and clean...

..they will perform better clean, in my experience...

..if you can't get the clutch dis-assembled, you can still clean it up fairly well...

..get a can or two of aerosol electrical contact cleaner...

..remove the clutch, spray all into the bell and pad area...

..if you have compressed air available, that would be a plus...

..but kinda try to keep the cleaner away from the bearings..the center of the assembly...

..don't want to wash out your grease...

..concentrate on the "bell" area...

..hell, even compressed air alone will remove quite a bit of crap..

Logged
..every mod (action) necessitates a (reaction) mod..

omfgdotcodotuk

  • Sr. Member
  • ****
  • Posts: 334
  • fookin quick gilera ice 50/70cc malossified ish
    • View Profile
Re: Naraku Drive Belt
« Reply #24 on: October 10, 2010, 10:40:55 AM »
I am asking santa (the missus lol) for a compressor this year,i need one in my life ;)
Logged
Never ride faster than your guardian angel can fly ;)

sidthesloth

  • Hero Member
  • *****
  • Posts: 2313
  • Kymco ZX50
    • View Profile
Re: Naraku Drive Belt
« Reply #25 on: October 10, 2010, 10:43:26 AM »
Quote from: omfgdotcodotuk on October 10, 2010, 10:40:55 AM
I am asking santa (the missus lol) for a compressor this year,i need one in my life ;)

You won't regret it, I have a little 2.5hp one, very, very handy.
Logged
ZX50, 47mm cyl. kit, TZR50 CDI. Michelin Pilot Sport tyres,
Next performance mod; pumping the tyres up.

sidthesloth

  • Hero Member
  • *****
  • Posts: 2313
  • Kymco ZX50
    • View Profile
Re: Naraku Drive Belt
« Reply #26 on: October 10, 2010, 10:46:50 AM »
What I should have put in my last post was that last Xmas, I received two vouchers for a local auto parts store from my in~laws, so I used them to buy a wall mounted retractable air hose, is absolutely magic, no more tangled hoses, is ratcheting to lock when extended and winds up, no hassle. :)
Logged
ZX50, 47mm cyl. kit, TZR50 CDI. Michelin Pilot Sport tyres,
Next performance mod; pumping the tyres up.

omfgdotcodotuk

  • Sr. Member
  • ****
  • Posts: 334
  • fookin quick gilera ice 50/70cc malossified ish
    • View Profile
Re: Naraku Drive Belt
« Reply #27 on: October 10, 2010, 12:09:31 PM »
lol sid that retractable hose just made the list as well,i opened the cvt case and my gosh what a mess looked like a black sand storm had ripped thro there,had to brush it out before i replaced the belt on the ice compressed air would have been a god send,i was gonna go a lil longer belt wise but i opted for the standard piaggio belt and im glad i did no slippage and no slip from cold like the belt that was in there,but i have lost top end speed,but i can live with that cos it just sets off from a standing start quicker ;D
Logged
Never ride faster than your guardian angel can fly ;)

An Error Has Occurred!

Call to undefined function split()
Back